DRAMC V2.2.0.2 (0)
MT751020 at Thu Mar 31 12:04:09 CST 2016 free bootbase
Memory size 64MB
flash base: bc000000
Found SPI Flash 16MiB GD25Q128 at 0xbc000000
Bootloader version: 3.1
Search PHY addr and found PHY addr=8
Not found TC Phy
Press reset button to boot command mode.
Press any key in 3 secs to enter boot command mode.
...................................
Decompress to 80002000 free_mem_ptr=80600000 free_mem_ptr_end=80780000
75xx: 0x0
Uncompressing [LZMA] ... done.
Linux version 2.6.36 (root@localhost) (gcc version 4.3.4 (GCC) ) #1 SMP Tue Nov8
ISPRAM0: PA=00310000,Size=00008000,enabled
DSPRAM0: PA=1dff8000,Size=00001000,enabled
flash_init: flash_base:bc000000
flash_init: flash_base:bc000000
memsize:64MB
Ralink MT751020 SOC prom init
bootconsole [early0] enabled
CPU revision is: 00019555 (MIPS 34Kc)
Determined physical RAM map:
memory: 03fe0000 @ 00020000 (usable)
Wasting 1024 bytes for tracking 32 unused pages
Zone PFN ranges:
Normal 0x00000020 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000020 -> 0x00004000
3 available secondary CPU TC(s)
PERCPU: Embedded 7 pages/cpu @81083000 s7264 r8192 d13216 u65536
pcpu-alloc: s7264 r8192 d13216 u65536 alloc=16*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16224
Kernel command line: es=1
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=0006498c
Readback ErrCtl register=0006498c
nmi base is 810c4200
Memory: 60660k/65408k available (3160k kernel code, 4748k reserved, 645k data, )
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
CPU frequency 648.00 MHz
Using 266.667 MHz high precision timer.
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
34K sync es set to 1.
Config7: 0x80080500
Limit of 4 TCs set
TLB of 64 entry pairs shared by 2 VPEs
VPE 0: TC 0 1 2, VPE 1: TC 3
IPI buffer pool of 16 buffers
CPU revision is: 00019555 ((null))
TC 1 going on-line as CPU 1
CPU revision is: 00019555 ((null))
TC 2 going on-line as CPU 2
CPU revision is: 00019555 ((null))
TC 3 going on-line as CPU 3
Brought up 4 CPUs
NET: Registered protocol family 16
MT7510_pcie_init
check pcie link up status:
isRC0_LINKUP=0
isRC1_LINKUP=1
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:01.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x200]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io disabled]
pci 0000:00:01.0: bridge window [mem 0x20000000-0x200fffff]
pci 0000:00:01.0: bridge window [mem pref disabled]
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
NET: Registered protocol family 8
NET: Registered protocol family 20
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
TC3162 hardware watchdog module loaded.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (ZLIB) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 118
io scheduler noop registered (default)
ttyS0 at I/O 0xbfbf0003 (irq = 1) is a TC3162
brd: module loaded
tc3162 mtd init: mt6573_nand_init enter
MediaTek MT6573 Nand driver init, version v2.0
tc3162: flash device 0x01000000 at 0x1c000000
tc3162: Found SPIFLASH 16MiB GD25Q128
Creating 7 MTD partitions on "tc3162":
0x000000000000-0x000000010000 : "bootloader"
0x000000010000-0x000000020000 : "romfile"
0x000000020000-0x00000016de44 : "kernel"
mtd: partition "kernel" doesn't end on an erase block -- force read-only
0x00000016de44-0x0000008ede44 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-y
0x000000020000-0x000000ec0000 : "tclinux"
0x000000ec0000-0x000000fc0000 : "jffs2"
0x000000fc0000-0x000001000000 : "reservearea"
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
RT3xxx EHCI/OHCI init.
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (947 buckets, 3788 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
GRE over IPv4 demultiplexor driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 212k freed
busybox init and set aff
init started: BusyBox v1.00 (2018.11.12-18:24+0000) multi-call binary
Sat Jan 1 00:00:00 UTC 2011
chmod: /userfs/profile.cfg: Read-only file system
module_sel: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
tcsmux version: tcsmux V1.1.0.0 (Nov 13 2018-02:22:21).
tcportbind version: tcportbind V1.1.0.0 (Feb 5 2014-17:25:04).
vlantag_drv_init
TCSUPPORT_IPV6
TC3162 LED Manager 0.1 init
tcledctrl version: tcledctrl V1.1.0.0 (Nov 13 2018-02:22:13).
tccicmd V1.1.0.0 (Nov 13 2018-02:22:18)
the number of cfg node is 76
register a node 0
register a node 1
regislogAccess_init ter a nodeLanguageSwitch_init 2
rvendorCfgFile_init egister a node 3rpstorm_init
reThe number of cache node is 5
[do_parse_romfile, 27]Start
[tc_parse_romfile, 245]Start
[tc_parse_romfile, 257]opername(/dev/mtdblock1)
[tc_parse_romfile, 260]check rom file(/dev/mtdblock1)
[check_romfile, 108]pathname(/dev/mtdblock1)
[check_romfile, 117]load XML file.
mxml: Bad control character 0x1f not allowed by XML standard!
[check_romfile, 174]2nd load XML file.
[check_romfile, 204]verify rom file.
[check_romfile, 217]return tree
Check romfile pass!
[tc_parse_romfile, 382]rechecknum(0)
[tc_parse_romfile, 389]laod backup romfile
[loadRomfile, 77](1)
[loadRomfile, 114]BK_ROMFILE_FLAG
mtd[readflash]:device=reservearea tclen=65536 tcoffset=0
Unlocking reservearea ...
Reading from reservearea to /tmp/tc_backupromfile ...
[BK_ROMFILE_FLAG]/userfs/bin/mtd readflash /tmp/tc_backupromfile 65536 0 reserva
[tc_parse_romfile, 396]check backup romfile
[check_romfile, 108]pathname(/tmp/tc_backupromfile)
[check_romfile, 117]load XML file.
mxml: Bad control character 0x1f not allowed by XML standard!
[check_romfile, 174]2nd load XML file.
[check_romfile, 204]verify rom file.
[check_romfile, 217]return tree
[tc_parse_romfile, 416]backup romfile is already exist.
Dualwan set wan_primary=8
Dualwan set wan_secondary=-1
killall: wpa_supplicant: no process killed
goto wlan_write!!killall: wpa_supplic
wlan_write---goto fopen!!ant: nWPSActiveStatus = NULL
o WPSOOBActive = NULL
prReCounterActive = NULL
ocWPSGenPinCode = NULL
ess killed
write_wlan_AutoChannelSkipList -(0x20)
write_wlan_profile() freq=0: Can not get the attribute wl0_HT_BADecline correct.
write_wlan_profile() freq=0: Can not get the attribugenerate miniupnpd.conf
te wl0_HT_STBC correctly so use the default value 1.
write_wlan_profile() freq=0: Can not get the attribute wl0_location_code correc.
_gen_upnp_conf
==>syslog_write error, get WriteFlashInterval value failed
==>syslog_write error, get UpdateInterval value failed
==>syslog_write error, get AllLogSave value failed
[cfgmgr](SIGCHLD:P207)..
insmod raeth driver
femac.c:v1.00-NAPI 29.Mar.2011
eth0: FE MAC Ethernet address: 60:xx:xx:xx:xx:xx
ifconfig: ra0: error fetching interface information: Device not found
7510_debug: dmt_base_addr : bf900000
ADSL DMT initialization starting
Begin AdslTaskInit.....
End AdslTaskInit
Begin to request IRQ 20
DMT:Succeed to request IRQ 20
Initializing ADSL F/W 5.5.2.10 ......
Initializing ADSL F/W ........ done
ra0 no private ioctls.
TCSUPPORT_WLAN
ra0 No such device
[main, 767]Init for web interface cfg node
lanHost_read: Create node LanHost !
TCSUPPORT_WLAN_MT7592
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
=== pAd = c1082000, size = 746648 ===
<-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
<-- RTMPAllocAdapterBlock, Status=0
device_id =0x7603
RtmpChipOpsHook(507): Not support for HIF_MT yet!
mt7603_init()-->
mt_bcn_buf_init(224): Not support for HIF_MT yet!
<--mt7603_init()
Cannot find device "br0"
Mirror/redirect action on
killall: tcapi: no process killed
cfg_manager start to init server socket
SIOCGIFFLAGS: No such device
Ebtables v2.0 registered
killall: ntpclient: no process killed
setup_receive:: bind...
pool.ntp.org: Unknown host
eth0: starting interface.
EPhy debug(8): tcPhyVerLookUp() in
MT7510FE, EPhy debug(8)(15): tcPhyVerLookUp() out
PhyPart debug: tcPhyInit() in , tcphyver=15, phyaddr=8, eco=0x0
phyaddr = 8
PhyPart debug: tcPhyInit() out , r31=0xb000
EPhy debug(12): tcPhyVerLookUp() in
MT7510Ge,Internal check flag: fgMT7510Ge_INT=0x0, eco=0x50003
EPhy debug(12)(16): tcPhyVerLookUp() out
PhyPart debug: tcPhyInit() in , tcphyver=16, phyaddr=12, eco=0x0
7510Ge, phyaddr= (12,12)
debug... ,phyaddr=12 ,eco=0x50003
PhyPart debug: tcPhyInit() out , r31=0xb000
Ralink HW NAT Module Enabled
IP check use Black List
device eth0 entered promiscuous mode
TCSUPPORT_WLAN: ifconfig
TCSUPPORT_WLAN_PERSSID_SWITCH disabled!
(2)Going to bring up WiFi interfaces!!
TCSUPPORT_WLAN_WDS
SSH
TC3162 hardware watchdog initialized
Ethernet Media-Type Support
monitorcfgmgr
Copyright (C) 2013 ASUS Corp. Renjie_Lee@asus.com
Jan 1 00:00:13 monitorcfgmgr[377]: [start monitorcfgmgr]
four ports
SIOCGIFFLAGS: No such device
interface elan.1 does not exist!
ERROR: trying to remove VLAN -:elan.1:- error: No such device
SIOCGIFFLAGS: No such device
interface elan.2 does not exist!
ERROR: trying to remove VLAN -:elan.2:- error: No such device
SIOCGIFFLAGS: No such device
interface elan.3 does not exist!
ERROR: trying to remove VLAN -:elan.3:- error: No such device
SIOCGIFFLAGS: No such device
interface elan.4 does not exist!
ERROR: trying to remove VLAN -:elan.4:- error: No such device
SIOCGIFFLAGS: No such device
interface elan.5 does not exist!
ERROR: trying to remove VLAN -:elan.5:- error: No such device
SIOCGIFFLAGS: No such device
interface elan.6 does not exist!
ERROR: trying to remove VLAN -:elan.6:- error: No such device
device eth0 is already a member of a bridge; can't enslave it to bridge br0.
ethphxcmd used greatest stack depth: 13688 bytes left
Added VLAN with VID == 1 to IF -:eth0:-
WARNING: VLAN 1 does not work with many switches,
consider another number if you have problems.
device elan.1 entered promiscuous mode
Added VLAN with VID == 2 to IF -:eth0:-
device elan.2 entered promiscuous mode
Added VLAN with VID == 3 to IF -:eth0:-
ip used greatest stack depth: 13656 bytes left
device elan.3 entered promiscuous mode
Added VLAN with VID == 4 to IF -:eth0:-
device elan.4 entered promiscuous mode
br0: port 1(eth0) entering disabled state
* Phyaddr=8 RegAddr=00 value=8000
* Phyaddr=9 RegAddr=00 value=8000
* Phyaddr=10 RegAddr=00 value=8000
* Phyaddr=11 RegAddr=00 value=8000
[ used greatest stack depth: 13632 bytes left
TSARM: MT7510 ATM SAR driver 1.0 init
atmInit
ATM SAR Time Base: 7065
atmInit 1.1 Version
ATM SAR Reset
==============================================
atm_init_wrappter
atm_init_wrappter
br2684_init
Mac = 60:xx:xx:xx:xx:xxpppoatm_init
==============================================
ATM SAR RX NAPI Mode
mt7510_netdev_start
atm_dev: MT7510 ATM Ethernet address: 60:45:CB:16:4D:D8
mt7510_atm_init: register_netdev success
mt7510_atm_init: open genenral device
mt7510_netdev_open
atm_dev: starting interface.
general device status: 3
atm_msg_buffer_init
txMsgNum: 720
rxMsgNum: 512
register autopvc cmd to sys
Channel:0, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0
Channel:1, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0
Channel:2, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0
Channel:3, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0
Channel:4, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0
Channel:5, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0
Channel:6, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0
Channel:7, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0
gzip used greatest stack depth: 13528 bytes left
[write_cur_romfile_in_flash, 456]write running romfile.
Unlocking romfile ...
Writing from /tmp/var/romfile.cfg.gz to romfile ...
[w]
[write_cur_romfile_in_flash, 464]write backup romfile in flash.
[write_backup_romfile]/userfs/bin/mtd writeflash /tmp/var/romfile.cfg.gz 65536 a
mtd[writeflash]:device=reservearea tclen=65536 tcoffset=0 tcfilelen =65536
Unlocking reservearea ...
Writing from /tmp/var/romfile.cfg.gz to reservearea ...
enter real action -----tclen:0x10000,tcoffset:0x0
writeflash: write 0 'st sector,start from 0x0,0x10000 bytes
writeflash: total write 0x10000 bytes
TCAPI save ok.
Jan 1 00:00:18 crond[595]: crond 2.3.2 dillon, started, log level 8
The test lab:255
log cicmd 0 (wan vdsl2 set sra on )
US bitswap on,DS bitswap on
log cicmd 1 (wan vdsl2 set bs_tx on )
log cicmd 2 (wan vdsl2 set bs on )
G.VECTOR on
gvt_ns_flag off
Set SNRM OFFSET = 5.0 db
Set Agc Vref1 = 65535 ; Vref2 = 65535 ; Vref3 = 65535
log cicmd 3 (wan vdsl2 set target_snrm 32767 )
PROFILE17A_MULTI_MODE
log cicmd 4 (wan vdsl set agc 65535 65535 65535 65535 )
log cicmd 5 (wan vdsl set upbo 255 )
log cicmd 6 (wan vdsl set sync_sym 10 )
G.inp mode
ANNEXA
annex auto-switch flag = 0
DLA: start
br0: port 5(elan.4) entering forwarding state
br0: port 5(elan.4) entering forwarding state
br0: port 4(elan.3) entering forwarding state
br0: port 4(elan.3) entering forwarding state
br0: port 3(elan.2) entering forwarding state
br0: port 3(elan.2) entering forwarding state
br0: port 2(elan.1) entering forwarding state
br0: port 2(elan.1) entering forwarding state
Ralink HW NAT Module Disabled
Ralink HW NAT Module Enabled
IP check use Black List
done
device br1 already exists; can't create bridge with the same name
check_and_set_iptv_ifname: a9fef1b1(169.254.241.177)
_ifconfig: name=br2 flags=1043 IFUP addr=169.254.241.177 netmask=255.255.0.0
check_and_set_iptv_ifname: a9fe828b(169.254.130.139)
_ifconfig: name=br3 flags=1043 IFUP addr=169.254.130.139 netmask=255.255.0.0
check_and_set_iptv_ifname: a9fe88eb(169.254.136.235)
_ifconfig: name=br4 flags=1043 IFUP addr=169.254.136.235 netmask=255.255.0.0
upd========================insmod iptable_filter=======================
ate_wan_state(wan0_, 5, 0)
update_wan_state(wan1_, 5, 0)
update_wan_state(wan2_, 5, 0)
update_wan_state(wan3_, 5, 0)
update_wan_state(wan4_, 5, 0)
update_wan_state(wan5_, 5, 0)
update_wan_state(wan6_, 5, 0)
update_wan_state(wan7_, 5, 0)
update_wan_state(wan8_, 0, 0)
update_wan_state(wan9_, 5, 0)
update_wan_state(wan10_, 5, 0)
update_wan_state(wan11_, 5, 0)
update_wan_state(wan12_, 5, 0)
========================insmod ipt_REJECT=======================
/etc/isp0.conf
/etc/isp1.conf
/etc/isp2.conf
/etc/isp3.conf
/etc/isp4.conf
/etc/isp5.conf
/etc/isp6.conf
/etc/isp7.conf
SIOCGIFFLAGS: No such device
/etc/isp8_0.conf
==>Error, socket or ioctl error for mulifctl
SIOCGIFFLAGS: No such device
SIOCSIFHWADDR: No such device
SIOCSIFADDR: No such device
Plugin libpppoe.so loaded.
RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5
pppd: unrecognipppd used greatest stack depth: 13392 bytes left
zed option 'nas8_0'
pppd version 2.4.5
Usage: pppd [ options ], where options are:
<device> Communicate over the named device
<speed> Set the baud rate to <speed>
<loc>:<rem> Set the local and/or remote interface IP
addresses. Either one may be omitted.
asyncmap <n> Set the desired async map to hex <n>
auth Require authentication from peer
connect <p> Invoke shell command <p> to set up the serial line
crtscts Use hardware RTS/CTS flow control
defaultroute Add default route through interface
file <f> Take options from file <f>
modem Use modem control lines
mru <n> Set MRU value to <n> for negotiation
See pppd(8) for more options.
/etc/isp10_7.conf
/etc/isp11.conf
/etc/isp12.conf
sh: /userfs/bin/zebra: not found
sh: /userfs/bin/ripd: not found
Radvd is disabled
dhcp6s is disabled!
info, udhcpd (v0.9.9-pre) started
error, Unable to open /etc/udhcpd.leases for reading
goto wlan_boot!!!Interface doesn't accept private ioctl...
set (8BE2): Network is down
goto write_wlan_first_profile()!!write_wlan_AutoChannelSkipList -(0x20)
write_wlan_first_profile() freq=0 : Can not get the attribute wl0_HT_BADecline .
write_wlan_first_profile() freq=0 : Can not get the attribute wl0_HT_STBC corre.
write_wlan_first_profile() freq=0 : Can not get the attribute wl0_location_code.
TX_BCN DESC a1fb8000 size = 320
RX[0] DESC a1fba000 size = 2048
RX[1] DESC a1fbb000 size = 2048
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Equal!
FW Version:CL173766-A
FW Build Date:20170925114906
CmdAddressLenReq:(ret = 0)
CmdFwStartReq: override = 1, address = 1048576
CmdStartDLRsp: WiFI FW Download Success
AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
efuse_probe: efuse = 10000002
RtmpChipOpsEepromHook::e2p_type=4, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=1
RtmpChipOpsEepromHook: E2P type(4), E2pAccessMode = 4, E2P default = 1
NVM is BIN mode
1. Phy Mode = 14
Cal Free IC!!
now bb MainSsid mac 60:xx:xx:xx:xx:xx
Country Region from e2p = ffff
tssi_1_target_pwr_g_band = 34
2. Phy Mode = 14
3. Phy Mode = 14
NICInitPwrPinCfg(14): Not support for HIF_MT yet!
NICInitializeAsic(585): Not support rtmp_mac_sys_reset () for HIF_MT yet!
mt_mac_init()-->
mt7603_init_mac_cr()-->
AsicSetMacMaxLen(1829): Set the Max RxPktLen=1024!
<--mt_mac_init()
WTBL Segment 1 info:
MemBaseAddr/FID:0x28000/0
EntrySize/Cnt:32/128
WTBL Segment 2 info:
MemBaseAddr/FID:0x40000/0
EntrySize/Cnt:64/128
WTBL Segment 3 info:
MemBaseAddr/FID:0x42000/64
EntrySize/Cnt:64/128
WTBL Segment 4 info:
MemBaseAddr/FID:0x44000/128
EntrySize/Cnt:32/128
AntCfgInit(2570): Not support for HIF_MT yet!
MCS Set = ff ff 00 00 01
networkmap is gn. launch it.
AsicSetRalinkBurstMode(4233): Not support for HIF_MT yet!
RTMPSetPiggyBack(879): Not support for HIF_MT yet!
AsicSetTxPreamble(4220): Not support for HIF_MT yet!
AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xa0
Main bssid = 60:45:cb:16:4d:d8
<==== rt28xx_init, Status=0
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
jiffies=ffff9928, POLLING_MODE_DETECT_INTV=300
ifconfig used greatest stack depth: 13200 bytes left
device ra0 entered promiscuous mode
br0: port 1(ra0) entering forwarding state
br0: port 1(ra0) entering forwarding state
RTMPIoctlMAC():wrq->u.data.length=18, pointer(7fe51240)=60150004=0003001c!
RTMPIoctlMAC():after trim space, ptr len=17, pointer(822d5000)=60150004=0003001!
ra0 mac:[0x21a04]:0003001c
RTMPIoctlMAC():wrq->u.data.length=18, pointer(7faf7be0)=60200618=D7E87D10!
RTMPIoctlMAC():after trim space, ptr len=17, pointer(822d5000)=60200618=D7E87D1!
ra0 mac:[0x10618]:d7e87d10
rai0 no private ioctls.
rai0 no private ioctls.
rai0 no private ioctls.
==>Set_Debug_Proc()
<==Set_Debug_Proc(RTDebugLevel = 0)
BusyBox v1.00 (2018.11.12-18:24+0000) multi-call Disable Virtual Server / Port .
binary
Usage: route [{add|del|delete}]
nf_conntrack_rtsp v0.6.21 loading
port #0: 554
nf_nat_rtsp v0.6.21 loading
insmod used greatest stack depth: 12992 bytes left
generate miniupnpd.conf
_gen_upnp_conf
launch upnp
start_miniupnpd. force(1)
stop upnp first
Unknown applet: add_ovpn_fw_rules
/userfs/bin/miniupnpd -P /var/log/upnpd.pid -f /var/tmp/miniupnpd.conf &
upnpd_boot
_gen_upnp_conf
start_miniupnpd. force(1)
stop upnp first
route: SIOC[ADD|DEL]/userfs/bin/miniupnpd -P /var/log/upnpd.pid -f /var/tmp/min&
RT: File exists
[write_cur_romfile_in_flash, 456]write running romfile.
Unlocking romfile ...
Writing from /tmp/var/romfile.cfg.gz to romfile ...
[w]
[write_cur_romfile_in_flash, 464]write backup romfile in flash.
[write_backup_romfile]/userfs/bin/mtd writeflash /tmp/var/romfile.cfg.gz 65536 a
mtd[writeflash]:device=reservearea tclen=65536 tcoffset=0 tcfilelen =65536
Unlocking reservearea ...
Writing from /tmp/var/romfile.cfg.gz to reservearea ...
enter real action -----tclen:0x10000,tcoffset:0x0
writeflash: write 0 'st sector,start from 0x0,0x10000 bytes
writeflash: total write 0x10000 bytes
TCAPI save ok.
killall: klogd: no process killed
ftp switch turn on
sip switch turn on
h323 switch turn on
rtsp switch turn on
l2tp switch turn on,sw_state=
iptables: Bad rule (does a matching rule exist in that chain?).
ipsec switch turn on,sw_state=
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: No chain/target/match by that name.
ifconfig: ppp80: error fetching interfa
#### wan_primary: []
ce information: Device not found
killall: utelnetd: no process killed
get_iptv_ifname: nas8_0
check_and_set_iptv_ifname: a9fe94c4(169.254.148.196)
_ifconfig: name=nas8_0 flags=1043 IFUP addr=169.254.148.196 netmask=255.255.0.0
nas8_0: No such device
wol_boot
client_list_boot. launch networkmap
arpstorm_boot
Arpstorm_Entry_runin=0
RTS debug message OFF!
cmd[0]=restart_pppoe_relay
cmd[1]=8
[1880 service:handle_notifications +41] running: 3 pppoe_relay
http_update_allowed_client-restrict_client(0): (0)clients
log cicmd 0 (wan dmt2 set largeD 2 )
start_pptpd: getpid= 569
init_ramusage()
msgget ok
set_msqid=0
ret_val=0
mtd[readflash]:device=reservearea tclen=65536 tcoffset=131072
Unlocking reservearea ...
Reading from reservearea to /var/log/tmp_file ...
Can't find Node(Info_dot1q), create it.
load: current_uptime = 0m, save_utime = 60m
decomp: fname=/var/tmp/rstats-speed.gz
decomp: gzip -dc /var/tmp/rstats-speed.gz > /var/tmp/rstats-uncomp != 0
load: speed_count = 0
load: read source= save_path=
load_history: fname=/var/tmp/rstats-history.gz
decomp: fname=/var/tmp/rstats-history.gz
Done.
decomp: gzip -dc /var/tmp/rstats-history.gz > /var/tmp/rstats-uncomp != 0
decomp: fname=/var/tmp/rstats-history.gz
decomp: gzip -dc /var/tmp/rstats-history.gz > /var/tmp/rstats-uncomp != 0
load_history: load failed
# Enable direct rule
stop_nat_rules: apply the redirect_rules!
iwpriv used greatest stack depth: 12596 bytes left
iptables-restor used greatest stack depth: 12332 bytes left
calc: add WIRED as #0
calc: sync WIRED
calc: add WIRELESS0 as #1
calc: sync WIRELESS0
calc: add ATM as #2
calc: sync ATM
grep used greatest stack depth: 12292 bytes left
Unknown applet: add_ovpn_fw_rules
Warning: Driver for device ra0 has been compiled with version 22
of Wireless Extension, while this program supports up to version 20.
Some things may be broken...
calc: add PTM0 as #3
calc: sync PTM0
calc: add PTM1 as #4
calc: sync PTM1
calc: add ETHERNETWAN as #5
calc: sync ETHERNETWAN
calc: add BRIDGE as #6
calc: sync BRIDGE
*reg=00001fe0 value:200d4008 (ext_switch:0)
Firmware version=[1.1.2.3]
Please press Enter to activate this console. Can't find Node(Vram), create it.
Can't find Node(Vram_Entry), create it.
Can't find Node(LogAccess_ToFile), create it.
|